Treatment of tomato paste wastewater by electrochemical and membrane processes: process optimization and cost calculation.

This study investigated the treatment of wastewater from tomato paste (TP) production using electrocoagulation (EC) and electrooxidation (EO). The effectiveness of water recovery from the pretreated water was then investigated using the membrane process. For this purpose, the effects of independent control variables, including electrode type (aluminum, iron, graphite, and stainless steel), current density (25-75 A/m2), and electrolysis time (15-120 min) on chemical oxygen demand (COD) and color removal were investigated. The results showed that 81.0% of COD and 100% of the color removal were achieved by EC at a current density of 75 A/m2, a pH of 6.84 and a reaction time of 120 min aluminum electrodes. In comparison, EO with graphite electrodes achieved 55.6% of COD and 100% of the color removal under similar conditions. The operating cost was calculated to be in the range of $0.56-30.62/m3. Overall, the results indicate that EO with graphite electrodes is a promising pretreatment process for the removal of various organics. In the membrane process, NP030, NP010, and NF90 membranes were used at a volume of 250 mL and 5 bar. A significant COD removal rate of 94% was achieved with the membrane. The combination of EC and the membrane process demonstrated the feasibility of water recovery from TP wastewater.

Compression stress-strain curve of lithium slag recycled fine aggregate concrete.

As one of the key materials used in the civil engineering industry, concrete has a global annual consumption of approximately 10 billion tons. Cement and fine aggregate are the main raw materials of concrete, and their production causes certain harm to the environment. As one of the countries with the largest production of industrial solid waste, China needs to handle solid waste properly. Researchers have proposed to use them as raw materials for concrete. In this paper, the effects of different lithium slag (LS) contents (0%, 10%, 20%, 40%) and different substitution rates of recycled fine aggregates (RFA) (0%, 10%, 20%, 30%) on the axial compressive strength and stress-strain curve of concrete are discussed. The results show that the axial compressive strength, elastic modulus, and peak strain of concrete can increase first and then decrease when LS is added, and the optimal is reached when the LS content is 20%. With the increase of the substitution rate of RFA, the axial compressive strength and elastic modulus of concrete decrease, but the peak strain increases. The appropriate amount of LS can make up for the mechanical defects caused by the addition of RFA to concrete. Based on the test data, the stress-strain curve relationship of lithium slag recycled fine aggregate concrete is proposed, which has a high degree of agreement compared with the test results, which can provide a reference for practical engineering applications. In this study, LS and RFA are innovatively applied to concrete, which provides a new way for the harmless utilization of solid waste and is of great significance for the control of environmental pollution and resource reuse.

Electrocoagulation in treatment of municipal wastewater- life cycle impact assessment.

The purpose of this study is investigation of electrocoagulation (EC) as a treatment of municipal wastewater, integrating life cycle impact assessment (LCIA) for assessing its environmental performance of investigated treatment. The study evaluated the effectiveness of EC in removing physico-chemical and microbial parameters using aluminum (Al) and iron (Fe) electrodes in monopolar and bipolar modes. Bipolar arrangement of Al(-)/Al/Al/Al(+) electrodes achieved the highest removals: 70% COD, 72% BOD5 followed by complete elimination of total phosphorous, turbidity and microbial parameters. This treatment was subject to investigation of the influence of reaction time (t = 10-60 min) on removals at higher current density (CD = 3.33 mA/cm2). In order to reduce energy consumption, the same reaction time range was used with a reduced CD = 2.33 mA/cm2. Following removal efficiencies obtained: 47-72% COD (higher CD) and 53-78% (lower CD); 69-75% BOD5 (higher CD) and 55-74% CD (lower CD); 12-21% NH4- (higher CD) and 7-22% NH4- (lower CD). Total P, NO3- and NO2- compounds showed the same removals regardless the CD. Decrease in current density did not influence removals of total suspended matter, turbidity, salinity as well as microbial parameters. The bipolar arrangement of Al(-)/Al/Al/Al(+) electrodes, assuming a lower CD = 2.33 mA/cm2 and t = 30 min, was assessed with the Recipe 2016Midpoint (H) and USEtox v.2 LCIA methods to explore the environmental justification of using EC for wastewater treatment. The LCIA results revealed that the EC process significantly reduces water eutrophication and toxicity for freshwater and marine ecosystems, but has higher impacts in global warming, fossil fuel consumption, human toxicity, acidification, and terrestrial ecotoxicity due to high energy consumption. This can be mainly explained by the assumption in the study that the EC precipitate is dispersed to agricultural soil without any pre-treatment and material recovery, along with relatively high energy consumption during the process.

Tuning a green carboxymethyl cellulose-based pre-tanning agent via peroxide oxidation for high chrome exhaustion in leather industry.

The low chrome uptake by collagen in the conventional tanning process leads to the pollution of the wastewater. Due to environmental concerns, leather scientists are already searching for innovative ways to produce pre-tanning agents as a high exhaustion chrome tanning auxiliary. Herein, a novel kind of pre-tanning agent is engineered by converting carboxymethyl cellulose (CMC) to oxidized carboxymethyl cellulose (OCMC) via the hydrogen peroxide process. FT-IR and carboxyl content analysis demonstrated the increase in carboxyl content after oxidation. After that, the obtained OCMC was utilized as a pre-tanning agent, resulting in a high exhaustion of chrome (92.76 %) which is 27.76 % more than conventional chrome tanning (65 %), and the amount of chrome in wastewater reduced to 7.24 %. The hydrothermal stability of wet-blue increased by increasing the uptake of chrome (Ts = 118 °C). The obtained crust leather represented excellent mechanical properties (Tensile strength: 305.68 kg/cm2; tear strength: 50 kg/cm) and desirable organoleptic properties. The environmental analysis signifies a significant step towards a cleaner and sustainable tanning process (COD = 1600, BOD5 = 560 mg/L) compared to the conventional chrome tanning process. Consequently, the obtained results offer a green pre-tanning agent to meet the requirements of the sustainable development of the leather industry.

Methacrylic acid in situ modified steel converter slag/natural rubber composites: Resourceful utilization of steelmaking solid wastes.

As a by-product of the steelmaking industry, the large-volume production and accumulation of steel converter slag cause environmental issues such as land occupation and dust pollution. Since metal salts of unsaturated carboxylic acid can be used to reinforce rubber, this study explores the innovative application of in-situ modified steel slag, mainly comprising metal oxides, with methacrylic acid (MAA) as a rubber filler partially replacing carbon black. By etching the surface of steel slag particles with MAA, their surface roughness was increased, and the chemical bonding of metal methacrylate salt was introduced to enhance their interaction with the molecular chain of natural rubber (NR). The results showed that using the steel slag filler effectively shortened the vulcanization molding cycle of NR composites. The MAA in-situ modification effectively improved the interaction between steel slag and NR molecular chains. Meanwhile, the physical and mechanical properties, fatigue properties, and dynamic mechanical properties of the experimental group with MAA in-situ modified steel slag (MAA-in-situ-m-SS) were significantly enhanced compared with those of NR composites partially filled with unmodified slag. With the dosage of 7.5 phr or 10 phr, the above properties matched or even exceeded those of NR composites purely filled with carbon black. More importantly, partially replacing carbon black with modified steel slag reduced fossil fuel consumption and greenhouse gas emission from carbon black production. This study pioneered an effective path for the resourceful utilization of steel slag and the green development of the steelmaking and rubber industries.

Determination of potentially toxic elements bioaccumulated in the commercially important pelagic fish narrow-barred Spanish mackerel (Scomberomorus commerson).

Anthropogenic activities have increased the discharge of marine contaminants threatening marine life. Small gulfs, such as the Arabian Gulf, are vulnerable to accumulating potentially toxic elements in marine species due to slow water exchange. The concentration of 21 elements was determined in the tissues of Scomberomorus commerson from Umm Al Quwain (United Arab Emirates) and Bandar Abbas (Iran). Chromium, Copper, and Iron exceeded internationally established maximum permissible limits. Sites could not be distinguished based on Principle Component Analyses of elements. Elevated Cu and Cr in muscle are of concern to marine species as well as humans. Metal Pollution Index showed a significant difference between sites, with 20.34 % and 100 % of individuals suffering high metal toxicity and poor body conditions, respectively. The Arabian Gulf is experiencing an increase in discharge of industrial wastes. Implementation of strict policies to reduce discharge of toxic substances is required to protect marine organisms and humans.

Sedimentary environmental quality of a biosphere reserve estuary in southwestern Iberian Peninsula.

The Huelva estuary is formed by the common mouths of the Odiel and Tinto Rivers, and inside this ecosystem is the biosphere reserve of the Odiel saltmarshes. This ecosystem has been historically affected by acid mine drainage (AMD) and by releases of pollutants from five phosphoric acid industrial plants and phosphogypsum (PG) waste stacks located in the area. This study carried out a comprehensive assessment of the environmental impact of the biosphere reserve of the Odiel saltmarshes. To this end, it was necessary to find a suitable sedimentary background (Piedras River in our case). To quantify this impact, several pollution indexes were used. According to the values reached by the indexes, this impact was classified as "serious" pollution for most trace elements, excepting the deepest layers, and "low-moderate" pollution for the 238U-series radionuclides, while no pollution for the 232Th-series and 40K radionuclides was found as expected.

Sustainable approaches in concrete production: An in-depth review of waste foundry sand utilization and environmental considerations.

This review critically evaluates the potential of Waste Foundry Sand (WFS) as a substitute for fine aggregate in concrete, conducting a comparative analysis of its physical and chemical properties against those of natural sand. The study synthesizes findings from various research experiments to determine concrete's most effective WFS replacement percentage. It compiles and analyzes data on how different WFS ratios affect concrete's mechanical properties, including modulus of elasticity and compressive strength. The review also consolidates research on the impact of WFS on concrete's workability, density, and flowability. A key finding is that WFS, categorized as a non-hazardous waste, possesses a diverse particle size distribution, rendering it suitable for recycling in various industrial applications.The study identifies that a 20%-30% replacement of WFS in concrete significantly improves properties such as voids, specific gravity, and density. However, it is essential to note that exceeding a 30% WFS replacement can result in increased carbonation depth and decreased resistance, primarily due to sulfur trioxide (SO3). Further observations indicate that incorporating higher levels of WFS in self-compacting concrete reduces its flowability and increases water permeability. Moreover, the review highlights the regulatory and classification challenges associated with using WFS, particularly its classification as waste, which hampers its widespread adoption in construction. In conclusion, the study recommends implementing End-of-Waste (EoW) regulations to facilitate sustainable recycling and environmental protection. Additionally, it includes a bibliometric analysis of foundry sand research spanning from 1971 to 2020, providing a comprehensive summary of the field's historical and recent developments.

Review on physical performance, modification mechanisms, carbon emissions and economic costs of recycled aggregates modified with physical enhancement technologies.

With the continuous advancement of urban renewal, the application of recycled aggregates (RA) is a win-win measure to solve the treatment of construction waste and provide the required building materials. However, the existence of a large amount of old adhesive mortar (OAM) makes it difficult for RA to equivalently replace natural aggregates (NA) due to their higher water absorption and crushing index, as well as a lower apparent density. From the published literature on enhancing RA, the most mature and easiest method for construction is physical enhancement technology. Therefore, through a review of recent related researches, this article summarizes and compares the modification effects of mechanical grinding technology, traditional heating and grinding technology, and microwave heating technology on the physical properties of RA, including water absorption, apparent density, and crushing value. The related modification mechanisms were discussed. Additionally, the impacts of different physical enhancement technologies on the environment and economy effects are assessed from the perspectives of carbon emissions and cost required during processing. Based on multi-criteria analysis, microwave heating technology is more efficient and cleaner, which is the most recommended in the future.

Deep resource utilization of hazardous arsenic-alkali slag: Thermodynamic analysis, mechanism investigation and process optimization.

The best solution to address environmental pollution caused by arsenic-containing hazardous waste is to prepare high-purity elemental arsenic from such waste. The key to this approach lies in the efficient separation of arsenic from various impurities. This paper presents a viable solution for producing high-purity elemental arsenic from arsenic-alkali slag, and the keylies in utilizing the selective precipitation of magnesium ammonium arsenate (MgNH4AsO4) to achieve efficient separation of arsenic from alkali, antimony, and other impurities. Thermodynamic analysis and hydrometallurgical condition experiments indicate that in complex alkaline arsenic-containing solutions, over 90% of arsenic components can selectively precipitate in the form of MgNH4AsO4. The content of arsenic in the resulting precipitate reaches approximately 30%, while the content of antimony is below 0.1%. This achieves efficient enrichment of arsenic and preliminary separation of impurities in complex arsenic-alkali slag. Thermodynamic analysis and pyrometallurgical condition experiments demonstrate that the precipitate of MgNH4AsO4 can be reduced to elemental arsenic with an arsenic content reaching 99.85%, and an antimony content as low as 0.05%. This achieves a profound separation of arsenic from impurities. Based on the research presented in this paper, a production line was established that enables the deep resource utilization of arsenic-alkali slag.

Insights into Full-congener Profiles of Chlorinated Benzenes in Fly and Bottom Ash: Case Study in Vietnamese Industrial and Municipal Waste Incinerators.

Chlorinated benzenes (CBzs) are a group of organic pollutants, which have been industrially or unintentionally produced through various chemical and thermal processes. Studies on full congener profiles of CBzs in waste and environmental samples are relatively limited and not updated. In the present study, concentrations of 12 CBzs were determined in fly ash (FA) and bottom ash (BA) samples collected from one municipal waste incinerator (MWI) and one industrial waste incinerator (IWI) in northern Vietnam. Levels of Σ12CBzs were higher in bottom ash (median 25.3; range 1.59-45.7 ng/g) than in fly ash (median 7.30; range 1.04-30.0 ng/g). The CBz profiles were dominated by di- and tri-chlorinated congeners with the major congeners as 1,2,4-TCB, 1,2,3-TCB, 1,2-DCB, and 1,3-DCB. However, CBz profiles varied greatly between sample types and incinerators, implying differences in input materials, formation pathways, and pollutant behaviors. Incomplete combustion is possibly responsible for high levels of CBzs in industrial bottom ash. The emission factors of Σ12CBzs ranged from 21 to 600 µg/ton for fly ash and from 190 to 4570 µg/ton for bottom ash, resulting in annual emissions of about 6 and 3 g/year for the IWI and MWI, respectively. Our results suggest additional investigations on industrial emission and environmental occurrence of all 12 CBzs rather than solely focusing on regulated congeners like hexachlorobenzene and pentachlorobenzene.

Development and techno-economic analysis of Grewia biopolymer-based dual coagulant system for wastewater treatment at pilot scale.

Use of Grewia biopolymer as a natural coagulant aid was explored in a dual-coagulant system (conventional coagulant + biopolymer) for wastewater treatment. Such use not only improved turbidity removal efficiency over a wide pH range (5-9) but also helped reducing the concentration demand of inorganic coagulants by 25-50 %. Response surface methodology was employed for investigating the interaction between factors (initial pH, coagulant, and biopolymer concentration) affecting coagulation/flocculation of aqueous laterite suspension, and process optimization for more than 80 % turbidity removal in the desired final pH range (6-7). Mechanisms potentially involved in coagulation/flocculation using biopolymer was elucidated. Techno-economic assessment indicated the feasibility of pilot-scale production of the biopolymer and its use in wastewater treatment. This study demonstrates that Grewia biopolymer has the potential to be used as a coagulant aid and will help researchers select appropriate markets for further cost reduction and successful implementation of biopolymer-based wastewater treatment.

Removal of lead in water by coagulation flocculation process using Cactus-based natural coagulant: optimization and modeling by response surface methodology (RSM).

The aim of this research is to study the ability of Cactus leaves to act as a biocoagulants for the removal of lead in water. Different solvents, such as distilled water, NaCl, NaOH, and HCl, were used as chemical activators to extract the active components from the Cactus. The Cactus was utilized as an organic coagulant in five different forms: (i) Cactus juice (CJ); Cactus extract using (ii) distilled water (C-H2O); (iii) NaCl at 0.5 M concentration (C-NaCl); (iv) NaOH at 0.05 M concentration (C-NaOH); and (v) HCl at 0.05 M concentration (C-HCl). In order to establish the optimal conditions for the coagulation, this study employed the jar test as an experimental technique and the Box-Behnken design (BBD) as an experimental approach. According to BBD, there are three factors (k = 3), namely pH, biocoagulant dosage, and settling time. The R2 and R2 adjusted for all coagulants were close to 100%, confirming the validity of all the mathematical models. The results were significant; the highest lead removal efficiencies were 98.11%, 98.34%, 95.65, 96.19%, and 97.49%, utilizing CJ, C-H2O, C-NaCl, C-HCl, and C-NaOH as natural coagulants. The Cactus has been characterized using FTIR, XRD, and SEM to identify the active components that remove lead.

Recent advances in eco-friendly technology for decontamination of pulp and paper mill industrial effluent: a review.

The economic development of a country directly depends upon industries. But this economic development should not be at the cost of our natural environment. A substantial amount of water is spent during paper production, creating water scarcity and generating wastewater. Therefore, the Pollution Control Board classifies this industry into red category. Water is used in different papermaking stages such as debarking, pulping or bleaching, washing, and finishing. The wastewater thus generated contains lignin and xenobiotic compounds such as resin acids, chlorinated lignin, phenols, furans, dioxins, chlorophenols, adsorbable organic halogens (AOX), extractable organic halogens (EOCs), polychlorinated biphenyls, plasticizers, and polychlorinated dibenzodioxins. Nowadays, several microorganisms are used in the detoxification of these hazardous effluents. Researchers have found that microbial degradation is the most promising treatment method to remove high biological oxygen demand (BOD) and chemical oxygen demand (COD) from wastewater. Microorganisms also remove AOX toxicity, chlorinated compounds, suspended solids, color, lignin, derivatives, etc. from the pulp and paper mill effluents. But in the current scenario, mill effluents are known to deteriorate the environment and therefore it is highly desirable to deploy advanced technologies for effluent treatment. This review summarizes the eco-friendly advanced treatment technologies for effluents generated from pulp and paper mills.

Microbial intervention improves pollutant removal and semi-liquid organo-mineral fertilizer production from olive mill wastewater sludge and rock phosphate.

Olive mill wastewater sludge (OMWS) represents a residual pollutant generated by the olive oil industry, often stored in exposed evaporation ponds, leading to contamination of nearby land and water resources. Despite its promising composition, the valorization of OMWS remains underexplored compared to olive mill wastewater (OMW). This study aims to identify potent native microbial species within OMWS suitable for bioremediation and its transformation into a high-value organic fertilizer. The microbial screening, based on assessing OMWS tolerance and phosphate solubilization properties in vitro, followed by a singular inoculation using a mixture of OMWS and rock phosphate (RP). Identification of FUN 06 (Galactomyces Geotrichum), a fungal species, employed as an inoculant in the treatment of sterile OMWS supplemented with RP. Results demonstrate that fungal inoculation notably diminished OMWS phytotoxicity while enhancing its physicochemical parameters, nutrient concentrations, and removal of toxic organic compounds by up to 90% compared to the control, and enhances plant growth, offering a sustainable approach to tackle environmental concerns. Additionally, metataxonomic analysis unveiled FUN 06's propensity to enhance the presence of microbial species engaged in pollutant degradation. However, higher RP dosage (10%) appeared to adversely affect bioprocess efficiency, suggesting a potential dose-related effect. Overall, FUN 06, isolated from OMWS evaporation ponds, shows promise for effective bioremediation and sustainable reuse. In fact, our results indicate that targeted microbial inoculation stands as an effective strategy for mitigating pollutants in OMWS, facilitating its conversion into a nutrient-rich organo-mineral fertilizer suitable for direct use, promoting its beneficial reuse in agriculture, thereby presenting a promising avenue for olive oil waste management.

Green industry work: production of FeCl3 from iron and steel industry waste (mill scale) and its use in wastewater treatment.

Mill scale (MS) is considered to be a significant metallurgical waste, but there is no economical method yet to utilize its metal content. In this study, which covers various processes in several stages, the solution of iron in MS, which is the Iron and Steel Industry (I&SI) waste, as FeCl3 (MS-FeCl3) in the thermoreactor in the presence of HCl, was investigated. In the next step, the conditions for using this solution as a coagulant in the treatment of I&SI wastewater were investigated using the jar test. The results of the treated water sample were compared by chemical oxygen demand (COD), total suspended solids (TSS), color, and turbidity analyses using commercial aluminum sulfate (Al2(SO4)3) and FeCl3 (C-FeCl3). Additionally, heavy metal analyses were conducted, and the treatment performance of three coagulants was presented. Accordingly, while 2.0 mg/L anionic polyelectrolyte was consumed at a dosage of 4.05 mg/L Al2(SO4)3 at pH 7.0, 0.25 mg/L anionic polyelectrolyte was consumed at a dosage of 1.29 mg/L at pH 5.0 in the C-FeCl3 and MS-FeCl3 studies. Also, Fe, Cr, Mn, Ni, Zn, Cd, Hg, and Pb removal efficiencies were over 93.56% for all three coagulant usage cases. The results showed that the wastewater treatment performance of MS-FeCl3 by the recycling of MS, which is an I&SI waste, was at the same level as C-FeCl3. Thus, thanks to recycling, waste scale can be used as an alternative to commercial products for green production.

Successive process for efficient biovalorization of Brewers' spent grain to lignocellulolytic enzymes and lactic acid production through simultaneous saccharification and fermentation.

This study aimed to increase the value of brewers' spent grain (BSG) by using it as feedstock to produce lignocellulolytic enzymes and lactic acid (LA). Twenty-two fungal strains were screened for lignocellulolytic enzyme production from BSG. Among them, Trichoderma sp. showed the highest cellulase activity (35.84 ± 0.27 U/g-BSG) and considerably high activities of xylanase (599.61 ± 23.09 U/g-BSG) and ß-glucosidase (16.97 ± 0.77 U/g-BSG) under successive solid-state and submerged fermentation. The processes were successfully scaled up in a bioreactor. The enzyme cocktail was recovered and characterized. The maximum cellulase and xylanase activities were found at pH 5.0 and 50 °C, and the activities were highly stable at pH 4-8 and 30-50 °C. The enzyme cocktail was applied in simultaneous saccharification and fermentation of acid-pretreated BSG for LA production. The maximum LA obtained was 59.3 ± 1.0 g/L. This study has shown the efficient biovalorization of BSG, and this approach may also be applicable to other agro-industrial wastes.

CODD: A benchmark dataset for the automated sorting of construction and demolition waste.

This study presents the Construction and Demolition Waste Object Detection Dataset (CODD), a benchmark dataset specifically curated for the training of object detection models and the full-scale implementation of automated sorting of Construction and Demolition Waste (CDW). The CODD encompasses a comprehensive range of CDW scenarios, capturing a diverse array of debris and waste materials frequently encountered in real-world construction and demolition sites. A noteworthy feature of the presented study is the ongoing collaborative nature of the dataset, which invites contributions from the scientific community, ensuring its perpetual improvement and adaptability to emerging research and practical requirements. Building upon the benchmark dataset, an advanced object detection model based on the latest bounding box and instance segmentation YOLOV8 architecture is developed to establish a baseline performance for future comparisons. The CODD benchmark dataset, along with the baseline model, provides a reliable reference for comprehensive comparisons and objective assessments of future models, contributing to progressive advancements and collaborative research in the field.

New materials-based on gelatin coordinated with zirconium or aluminum for ecological retanning.

Ecological retanning agent is an effective way to solve the pollution source of leather manufacturing industry. In this study, the gelatin from chrome-containing leather shavings in the leather industry was used to realize sustainable leather post-tanning. The gelatin hydrolysate (GH) coordinated with Zr4+ or Al3+ to prepare eco-friendly retanning agents GH-Zr and GH-Al. The successful coordination between GH and metal ions was characterized by FTIR and XPS. The retanning agents were characterized by FTIR curve-fitting and circular dichroism spectroscopy. The results showed that the conformation of the secondary structure of the polypeptide became ordered and stable after coordinating with the metal ions. The particle size and weight average molecular weight of the retanning agents were ~1700 nm and ~2100, respectively, measured by nanoparticle size analyzer and gel permeation chromatography (GPC). The retanning agents were applied to retanning of chrome tanned leather and glutaraldehyde tanned leather. The abundant free amino from retanning agents can consume the free formaldehyde. Meanwhile, retanning agents can effectively improve the multiple binding sites, resulting in favorable thickening rate (>110 %) and excellent dye and fatliquor absorption rate with ~99.91 % and ~93.18 %. Thus, this strategy can provide a viable choice for solid leather waste and sustainable development of the leather industry.

Isolation and identification of metallotolerant bacteria with a potential biotechnological application.

Mining has led to severe environmental pollution in countries with exhaustive mining production and inadequate industrial waste regulation. Microorganisms in contaminated sites, like mine tailings, have adapted to high concentrations of heavy metals, developing the capacity of reducing or removing them from these environments. Therefore, it is essential to thoroughly characterize bacteria present in these sites to find different ways of bioremediation. In this regard, in this study, an enrichment and isolation procedure were performed to isolate bacteria with lower nutritional requirements and high tolerance to Cu(II) and Fe(II) from two Sonoran River basin mining tails. Two Staphylococcus species and a Microbacterium ginsengisoli strain were isolated and identified from the San Felipe de Jesús mining tail. Also, three strains were isolated from the Nacozari de García mining tail: Burkholderia cenocepacia, Sphingomonas sp. and Staphylococcus warneri. Significant microbiological differences were found between the two sites. All these species exhibited tolerance up to 300 mg/L for Cu (II)-Fe (II) solutions, indicating their capacity to grow in these conditions. Moreover, a consortium of isolated bacteria was immobilized in two different biocomposites and the biocomposite with larger pore size achieved greater bacterial immobilization showcasing the potential of these bacteria in biotechnological applications.